A condition-based selection guide for linear guide rail end seals and side seals: what each seal actually does, the working conditions that justify added sealing, the friction and length trade-offs, how to state seal requirements on an order, and the maintenance points to check once the machine is running.
The linear guide rail end seal is a small, low-cost part of the carriage block, and it is the part most often left out of an order. That is usually fine, until the application puts abrasive dust, machining chips, coolant splash or swarf near the rail. This guide explains what end seals and side seals do, the conditions under which they belong in the specification, how the trade-offs work, and how to write the requirement so the supplier ships the right configuration.
- End seals protect the carriage rolling elements from contamination entering along the rail; side seals cover the gap at the block ends and flanks.
- The decision is driven by the environment around the rail, not by load rating or stroke length.
- Seals add sliding friction and can affect overall carriage length; exact values must come from the datasheet for the specific block size.
- Specify seals as part of the model and option string on the order, and add the seal check to the preventive maintenance routine.
What end seals and side seals actually do
A linear guide carriage carries a row of recirculating balls or rollers along the rail raceway. The end caps close the recirculation path at each end of the block, and the end seals sit between the end cap and the rail, wiping the rail surface as the carriage moves. Their job is to limit what enters the ball or roller circuit along the rail: fine dust, grinding powder, machining chips and liquid that would otherwise migrate into the bearing path.
Side seals cover the interface at the flanks of the block, where contamination can also reach the raceway from the side. For a flange-type block on a machined frame, and for a wide-body block with a low rail, the exposed flank area differs, which is why the available seal options differ between product series.
What a seal does not do is replace a housing or a cover. If the rail runs in an open area with heavy chip generation, a seal reduces the rate at which contamination reaches the raceway; it does not make a machine clean-tight. That distinction matters when you are specifying protection for a machine that operates near a cutting zone versus one inside an enclosure.
Our two carriage lines and their documented seal options
Two blocks in the DF catalog carry defined seal information, and buyers comparing sealable options usually work between them:
| Series | Seal options listed | Stated protection class | Reference rating (size CA) |
|---|---|---|---|
| HGH flange-type carriage block | End seal and side seal available | IP40 | HGH20CA: 18.0 kN dynamic, 29.5 kN static |
| HGW wide-body carriage block | Three-seal option, dual lubrication ports | Confirm with datasheet | HGW25CA: 28.4 kN dynamic, 42.1 kN static |
Both series pair with the HGR series heavy-duty guideway rail, which is listed as 55# steel hardened to HRC 58-62; the HGR20 rail is rated 16.7 kN dynamic and 26.7 kN static. The rail grade tells you something about the seal question: a hardened raceway is the surface the seal wipes, and abrasive particles trapped at that interface are what the seal is meant to keep away from the rolling path.
The HGH is the flange-type block, mounted through the flange body. Its seal set is the common starting point for general machinery and automation frames. The HGW wide-body block has a lower, broader profile; its three-seal option and dual lubrication ports point to applications where the block is exposed on more faces or where lubrication points need to be reachable from either side.
Working conditions that justify seals
The conditions below are a practical decision list. Each one describes a condition around the rail that changes what reaches the carriage, and therefore what should be on the order.
Specify end seals when
- Abrasive dust is present β foundry sand, casting dust, carbon black, cement powder, stone cutting fines. Fine particles that pass a bare end cap reach the raceway and stay there.
- Machining chips or swarf fall on or near the rail. A seal wipes the rail so chips are pushed aside rather than carried into the recirculation path.
- Liquid splash or coolant mist reaches the rail area. End seals limit liquid migration along the rail surface; where the block is also exposed from the side, add side seals.
- The machine operates in an environment where the rail cannot be covered or housed, and the carriage is the last barrier between the environment and the rolling elements.
- Maintenance access is infrequent. Where re-lubrication and inspection intervals are long, a seal gives the carriage more margin against contamination between service visits.
Add side seals when
- The block flanks are exposed rather than buried in a machined pocket β typical for wide-body blocks and for blocks mounted on open frames.
- Contamination reaches the rail from the side rather than from above, for example in a horizontal machine axis where chips collect on the rail flange.
- Cleaning operations direct spray at the carriage from the side.
- The application has both dust and splash, and the wiping face alone is not enough to cover the exposed gap at the block ends.
Seals are not the deciding option when
- The rail is inside a closed housing with positive filtration β the seal adds friction without a corresponding reduction in contamination reaching the raceway.
- The carriage moves in a clean, dry environment with no chip generation and no liquid (bench automation, clean assembly stations, laboratory positioning).
- The dominant risk is large solid debris such as broken tool fragments or weld spatter, which a wiping seal will not stop; that calls for a physical cover or a different protection arrangement.
If an application sits near a boundary β intermittent splash on a horizontal axis, for example β specify the side seals and check the datasheet friction figures. The cost of the option is usually much lower than the cost of a change order after the machine is built.
The trade-offs: friction and length
Two costs come with sealing, and both should be evaluated before the option is locked in.
The first is sliding friction. A seal presses against the rail and adds drag proportional to the wiping contact. The exact friction increase depends on seal design and block size, and is given per datasheet for the specific model; do not extrapolate from another size. Where a small drive motor is already near its torque margin, this drag is the number to check, because it is added to the rolling resistance of the loaded carriage.
The second is length. Seals sit between the end cap and the rail, so a sealed block can have a different overall length and a different mounting reference than the unsealed version of the same size. If the machine design fixes the distance between the end of the block and the next component, or fixes the stroke end positions, confirm the sealed block dimensions on the datasheet before releasing the drawing. The right time to check is the drawing review, not the assembly bench.
Neither trade-off is large in absolute terms for typical automation sizes. Neither is zero. The selection question is whether the contamination risk in your application is worth the friction and the dimensional change β and that is answered by the environment, not by the load rating table.
How to specify seals when ordering
Seals are a configuration item, so they need to appear in the model designation and in the written order, not only in a conversation. A clear request contains the following:
- Series and size: for example HGH20CA or HGW25CA, so the block size and the rating are unambiguous.
- Seal requirement: end seal only, or end seal with side seals; for the HGW, state that the three-seal option is required.
- Preload: the HGH series lists preload options C0, C1 and C2. Preload choice affects stiffness and running characteristics and is separate from the seal choice, so state it explicitly.
- Quantity and MOQ: both series carry an MOQ of 50. If the initial requirement is below that and the seal option is critical, plan the order quantity accordingly rather than adding the seal later as a separate purchase.
- Protection expectation: state the environment in words β dust, chips, splash β so the supplier can confirm that the requested seal set matches the stated protection class. The HGH documentation states IP40; for the HGW, confirm the protection class with the datasheet.
- Dimensional check: ask for the sealed block length and mounting dimensions in writing, and hold the drawing review until they are confirmed.
A single line in the purchase order β model, seal set, preload, quantity β is enough to avoid the most common failure, which is receiving a sealed block when an unsealed one was drawn into the frame, or the reverse.
Maintenance checkpoints after commissioning
A seal is a wear item. Once the machine is running, the seal check belongs in the routine alongside lubrication:
- Inspect at every lubrication interval. Look at the wiping face of the end seal for embedded chips, hardened deposits or a visible gap between the seal lip and the rail.
- Check for contamination on the rail. A rail that shows a film of dust, dried coolant or fine swarf near the carriage is a sign the seal is not keeping up, or that it is damaged.
- Watch for a change in running resistance. A gradual increase in drive load on an axis whose duty has not changed can indicate seal drag from contamination buildup or a damaged seal lip.
- Replace seals, do not clean and refit. A seal that has lost its wiping contact is no longer doing its job.
- Keep the lubrication path clear. On the HGW the dual lubrication ports give two access points; confirm which port is used in service and keep it supplied so seal drag and rolling resistance stay within the design assumption.
Seal life depends on the environment and duty; there is no single interval that can be quoted for a series. Confirm the replacement guidance with the datasheet and set the inspection interval from the observed condition of the rail.
Where the decision lands
For a clean, enclosed automation axis, the unsealed or end-seal-only configuration is the simpler choice. For a machine running near a cutting zone, a casting line or a wet process, the end seal is a minimum and side seals are worth adding at the time of order. The HGH and HGW lines both give you a documented seal option to specify against, and the friction and length figures for each size are on the datasheet. Confirm the sealed dimensions in the drawing review, state the seal set on the order, and add the seal check to the lubrication routine.
Working through a seal decision for a specific frame? The HGH flange-type carriage block and the HGW wide-body carriage block pages list the available seal sets, and the HGR series rail details the matching guideway. State the model, seal set, preload and quantity in the inquiry to get a configuration that matches the environment.

