SEO

Linear Module Load Capacity: Ratings, Moments and Mounting

A published load rating for a linear module describes a specific, conditioned case β€” usually not your actual payload. This article explains what ratings include and exclude, why moment loads (Mx, My, Mr) set the real limit at an offset, how mounting orientation changes usable capacity, and how to compare two quotes line by line.

Linear Motion Engineering

A linear module datasheet lists a load capacity, and buyers usually go straight to that number. The trouble is that the number rarely describes the condition you will actually run. A carriage rated for a given mass placed directly above its centre is a different case from the same mass bolted on a bracket that reaches out, or the same module mounted vertically with the payload hanging off the end. Understanding what the rating covers β€” and what changes it β€” is the difference between a module that lasts and one that develops play, noise or premature wear.

What this article covers
  • Payload mass versus total moving mass
  • Static versus dynamic ratings
  • Allowable moment loads Mx, My and Mr
  • How horizontal, wall and vertical mounting change usable capacity
  • Why multiple carriages or spread mounting help
  • Duty cycle and acceleration margins
  • A short checklist for comparing two module quotes

Payload versus total moving mass

The figure a datasheet calls a load capacity normally refers to the mass the carriage can carry in addition to its own moving parts. Every module has a moving assembly β€” the carriage, the bearing block, the nut bracket, the screw support β€” and that assembly's mass is already accounted for in the design of the rail system. When you specify a module, the number you should compare against the rating is the mass of the tooling, fixture and workpiece that rides on the carriage, not the whole moving stack.

This distinction matters when you add a mounting plate, an adaptor, a gripper, or a rotary axis on top of the carriage. All of that becomes payload. A buyer who quotes a module against a workpiece weight while forgetting the fixture plate can easily end up above the intended margin without noticing. Add up everything that moves with the carriage and compare that figure with the rating β€” and where the datasheet does not state whether its rating includes the carriage mass, ask the supplier to clarify before you size the module.

Static versus dynamic ratings

Two kinds of ratings appear in linear motion documentation, and they answer different questions.

  • Static rating describes the load a module can hold while stationary or at very low speed, without permanent deformation of the rolling elements or raceways. It is about the structure surviving the load, not about life.
  • Dynamic rating describes the load the module can carry repeatedly over a defined travel distance and still reach its rated service life. It is the number that governs normal running duty.

For a moving application, the dynamic rating is the one to match against your payload. A module quoted on a static figure may be perfectly adequate for a clamping or positioning station that rarely moves, yet be overstressed by continuous reciprocation with the same mass. Confirm which figure the quote refers to, and under what travel and life assumption it was established. Do not assume a static figure implies the same dynamic capability.

Allowable moment loads: Mx, My and Mr

Mass sitting directly over the carriage centre is the easy case. Real tooling rarely does. A bracket that places the centre of gravity forward of, behind, or above the carriage creates a moment, and the rail and bearing system must resist it in addition to the vertical load. Datasheets typically list three allowable moments:

  • Mx β€” pitch moment, tending to tip the carriage forward or backward along the travel direction.
  • My β€” roll moment, tending to twist the carriage about the travel axis.
  • Mr (sometimes written Mz) β€” yaw moment, tending to rotate the carriage in the plane of the mounting surface.

These are usually specified separately, and they are not interchangeable. A tooling arrangement that is stiff in pitch but offset sideways may exhaust the allowable roll moment long before the vertical load rating is reached. The useful way to read them is together: calculate the moment each axis of your offset produces, then check each against its own allowable value, not just the sum of forces. The lever arm β€” the distance from the carriage centre to the centre of gravity of your payload β€” drives the moment, so a small mass on a long reach can load the module more severely than a heavier mass mounted close.

Practical rule

Keep the payload centre of gravity as close to the carriage centre as your tooling allows. Where an offset is unavoidable, treat the resulting moment as a design constraint in its own right, and confirm the allowable Mx, My and Mr for the exact module configuration with the supplier's datasheet before committing.

How mounting orientation changes usable capacity

The orientation of the module relative to gravity changes which loads and moments the bearing system has to resist, and therefore how much of the rated capacity is genuinely available.

  • Horizontal mounting. The payload's weight acts against the carriage in the direction the rail is designed to carry. This is the case most ratings are quoted around, and it is usually where usable capacity is highest.
  • Wall mounting (horizontal travel, vertical rail face). Gravity now acts sideways, producing a roll moment on the carriage proportional to the offset between the payload's centre of gravity and the rail face. Even a modest weight can use up allowable My quickly if the tooling projects out from the wall.
  • Vertical or Z-axis mounting. Gravity acts along the travel axis. The carriage must resist moments from the overhung payload on two axes at once, and in some arrangements a holding brake or a self-locking screw is needed to prevent the carriage dropping when power is removed. The usable payload for a given module is generally lower in vertical orientation than in horizontal, and the allowable moment figures become the binding constraint.

When you request a quote, state the mounting orientation explicitly. A capacity confirmed for horizontal use cannot be assumed to hold for a wall or vertical installation. Confirm the exact ratings in the datasheet for the orientation you intend to run.

Multiple carriages and spread mounting

Two techniques raise usable capacity without changing the module series.

  • Multiple carriages. Two or more carriages on the same rail can share the load, and, critically, can be spaced apart so that the payload sits between them. Spacing turns a large overhung moment into a smaller one because each carriage carries a share and the effective lever arm is reduced.
  • Spread mounting. Mounting the payload on a plate that spans both carriages, or widening the base fixing pattern, distributes force across a larger footprint and reduces the moment each bearing element sees.

The result is not simply "double the load." Load sharing depends on how evenly the carriages are loaded and how stiff the connecting plate is. A flexible plate that twists will concentrate load on one carriage. When considering multiple carriages, ask the supplier how the allowable moment values change for the configuration, and whether the shared capacity is stated for the assembly or per carriage. For a precision positioning application, the XY200 precision cross slide table with dual ball screw drive illustrates how two axes are combined in one assembly, where each axis carries its own share of the moving mass β€” confirm the exact ratings in the datasheet for the specific build.

Duty cycle and acceleration margins

A load rating is quoted for a defined life and a steady condition. Real machines accelerate, decelerate and reverse, and the forces during acceleration add to the static weight. For a horizontal module moving a mass, the force on the carriage during acceleration is the mass times acceleration, on top of the vertical weight if the motion is vertical. Higher acceleration, shorter move times and frequent reversals all raise the load the bearings see for the same payload.

Duty and speed also matter. A module running continuously at high speed accumulates travel distance quickly; the same load that is comfortable at low duty can erode life at high duty. Datasheets usually express this as a life figure tied to a rated load and distance. Buyers should ask what travel distance and load the published figure assumes, then compare it with their own expected duty. Where the margin is tight, a larger module, a lower acceleration profile, or additional carriages can restore it.

The drive components matter here too. A ball screw assembly transmits the axial force and can be a limiting element alongside the carriage. The SFU series rolled ball screw assembly is one of the drive options used in linear modules; its axial capacity and allowable speed should be checked against the same payload and acceleration profile as the carriage. Confirm the exact ratings in the datasheet.

A checklist for comparing two module quotes

Two quotes that look similar on the headline load figure can differ in what that figure actually covers. Use the following list to put both on the same footing.

CheckWhat to confirm in each quote
Rating typeIs the figure static or dynamic? Under what travel distance and life assumption?
Payload definitionDoes the rating include the carriage mass, or is it net payload? What mass must you add for your tooling?
Moment limitsAre Mx, My and Mr given separately? For which mounting orientation?
OrientationIs the rating stated for horizontal use only, or confirmed for your wall or vertical installation?
Multi-carriageIf two carriages are used, is capacity stated per carriage or for the assembly?
Duty and speedWhat rated load, speed and duty the published figure assumes, and how your application compares.
Drive componentsScrew or belt axial capacity and allowable speed checked against the same payload and acceleration.
MarginThe explicit safety margin the supplier recommends, and why.

If either quote omits the information needed to fill a row, that gap is the thing to resolve before comparison, not a reason to pick the higher number. A module that is correctly sized against your real centre of gravity, orientation and duty will hold accuracy far longer than one chosen on a headline load figure alone.

Frequently asked questions

Is the load capacity on a datasheet the weight I can put on the carriage?

Usually it refers to the payload β€” everything that moves with the carriage, including fixtures and tooling β€” but the definition varies between suppliers. Confirm whether the carriage's own mass is already included, then add up the total moving mass of your assembly.

Can I use a horizontal rating for a vertical Z-axis installation?

Not directly. Vertical mounting changes which loads and moments the bearing system carries and generally reduces usable payload for the same module. Ask for the rating confirmed for the orientation you will run.

Why do I need to worry about the moment if the total weight is within the load rating?

Because moment and force load the bearing system differently. A light payload on a long bracket can generate a moment that exceeds the allowable roll or pitch limit even though the mass is modest. Check each moment axis against its own allowable value.

Does adding a second carriage double the capacity?

It shares the load and, when spaced apart, reduces the effective moment. The actual gain depends on load distribution, plate stiffness and how the supplier states capacity for multi-carriage configurations β€” ask before assuming a specific increase.

How much margin should I leave?

There is no single figure that applies to all modules. The margin depends on your acceleration profile, duty cycle, required accuracy and the life assumption behind the published rating. Request the recommended margin for the exact module and application, and confirm the exact ratings in the datasheet.