A double-length LMK bush adds a second ball circuit and 1.8x the contact length of a standard single-circuit bearing. This article explains what that changes in load capacity, travel life and angular deflection, and which applications justify the extra length.
LMK linear bearing selection often comes down to one question: is the standard single-circuit bush enough, or does the application justify the longer, double-length version? The answer depends on load, travel life and how much angular deflection the axis can tolerate. This article explains what the second ball circuit changes and when it pays off.
Key takeaways
- A double-length LMK bush carries two independent ball recirculation circuits in one sleeve, giving 1.8 times the contact length of a standard single-circuit bearing.
- At LMK16UU, dynamic load capacity is 2,350 N versus 1,370 N for the single-circuit LMF16UU, and rated travel life is about 60 percent longer under equivalent load.
- The longer sleeve reduces angular deflection under moment loads on cantilevered axes, which matters for packaging machinery, textile equipment and high-duty reciprocating axes.
- For light loads and short strokes, a standard single-circuit bush remains the more economical choice.
What two independent ball circuits actually change
In a standard linear bush, one ball circuit carries the load over a short contact zone. A double-length LMK bush adds a second, independent recirculation circuit, so load is shared across roughly 1.8 times the contact length. That has three practical effects.
First, per-ball stress drops. With more balls in contact, each ball and each raceway segment carries less of the total load. Lower stress generally means less wear on the raceway over the same travel distance.
Second, load capacity increases. The LMK16UU is rated at 2,350 N dynamic and 3,680 N static, compared with 1,370 N dynamic for the single-circuit LMF16UU. This is not a marketing estimate; it is the published rating for the same 16 mm shaft size in two different designs.
Third, angular deflection under moment loads falls. On a cantilevered axis, where the load is offset from the bearing, the longer sleeve spreads the reaction over a greater distance. That reduces tilt and keeps the shaft alignment more stable during the stroke.
Double-length versus single-circuit: a direct comparison
| Feature | LMK double-length bush | Standard single-circuit bush (e.g., LMF) |
|---|---|---|
| Ball circuits | Two independent recirculation circuits | One circuit |
| Contact length | 1.8x standard | Baseline |
| Dynamic load at 16 mm bore | 2,350 N (LMK16UU) | 1,370 N (LMF16UU) |
| Static load at 16 mm bore | 3,680 N | Not stated here |
| Rated travel life | About 60% longer under equivalent load | Baseline |
| Angular deflection under moment | Lower | Higher |
The trade-off is length: a double-length bush needs more axial space and a longer housing. That is the main reason not every application uses one.
When a double-length bush pays off
High-duty reciprocating axes
If the axis runs continuously and the load is near the upper end of the single-circuit rating, the double-length bush gives more margin. The 60 percent travel-life increase under equivalent load means fewer replacements over the machine's service interval, which matters when downtime is costly.
Cantilevered or overhung loads
When the load is offset from the bearing centerline, the shaft sees a moment. A longer sleeve reduces angular deflection, keeping the shaft straighter and reducing edge loading on the balls. Packaging machinery and textile equipment often have this geometry, which is why they are typical uses.
Applications where deflection affects quality
In converting, printing or textile winding, small tilts can affect web tension or registration. The reduced deflection of a double-length bush helps maintain alignment over the stroke.
Retrofit or interchangeability
The LMK series uses a square 4-bolt flange to JIS B 1185 and is interchangeable with THK, IKO and MISUMI double-length flange bearings of the same size. If a machine was designed for a double-length bush, the LMK drops in without re-machining the housing.
When a standard single-circuit bush is enough
Not every axis needs the extra length. A standard bush is usually the better choice when:
- Loads are well below the single-circuit rating and travel is short.
- Space is tight and the housing cannot accommodate a longer sleeve.
- The axis is fully supported, with little or no moment load.
- Cost is the deciding factor and duty is light.
In those cases, the single-circuit design saves space and cost without sacrificing reliability. The LMF series square flange linear ball bearing is the direct single-circuit alternative for comparison.
Design and materials
The LMK series uses GCr15 chrome steel for the outer ring and balls, hardened to HRC 60-64. The retainer is PA66-GF, and UU double rubber seals close both ends to keep out dust and retain lubricant. Shaft diameters run from 6 to 50 mm (LMK 6 to LMK 50). H5 precision is available on request for LMK8 to LMK40, and the minimum order quantity is 100 pieces per size.
For full specifications, see the LMK series double-length linear ball bearing page.
Selection checklist
Before specifying a double-length bush, confirm:
- Dynamic and static load per bearing, including any moment component.
- Available axial space for the longer sleeve and housing.
- Required travel life and replacement interval.
- Shaft tolerance and required precision grade (H5 on request for LMK8 to LMK40).
- Interchangeability requirements with existing THK, IKO or MISUMI housings.
Frequently asked questions
Does a double-length bush fit the same housing as a single-circuit bush?
No. The longer sleeve needs a deeper housing. However, the LMK flange pattern is interchangeable with other double-length flange bearings of the same size.
Can I use a double-length bush on a short-stroke axis?
Yes, but the benefit is smaller. The extra load capacity and life are still present, but the space penalty may not be justified if loads are light.
Is H5 precision available for all sizes?
H5 precision is available on request for LMK8 to LMK40. For other sizes, consult the supplier.
What is the minimum order quantity?
MOQ is 100 pieces per size.
For application-specific advice, contact our technical team with your load, stroke and space constraints.

