SEO

Linear Bearing Bulk Orders: MOQ, Price Breaks and Packaging

Moving from sample linear bearings to volume purchasing changes what you need to verify. This article explains the MOQ 100 threshold used across LMUU, LMK and LME lines, how batch consistency is affected by seals and sleeve geometry, and how packaging decisions should be specified in a bulk purchase order.

Bulk purchasing guide

When a linear bearing requirement moves from evaluation samples to scheduled production, the questions change. Instead of asking whether a single unit fits the shaft, buyers ask what quantity triggers a bulk tier, whether the sealed parts in one carton match those in the next, and how the goods should be packed for the journey to the assembly line. This article sets out the MOQ, consistency and packaging points that apply to three common linear bearing lines: LMUU sealed extended-length, LMK double-length flange, and LME metric flange.

MOQ thresholds on the LM, LMK and LME lines

The three product families covered here share the same minimum order quantity: 100 pieces. That applies to the LMUU sealed extended-length series, the LMK double-length flange series, and the LME metric flange series. A buyer who needs 40 units for a pilot build is below the threshold for these volume lines; a buyer planning 100 or more per release cycle is not.

Read the 100 pieces as a per-line-item figure per order release. Whether a single 100-piece release can be split across bore sizes is a commercial point, not a catalog number: it has to be confirmed in writing with the supplier before the order is placed, and the same answer applies to any later release. The shaft size still affects how many SKUs sit inside one release. The LMK series covers shaft diameters from 6 to 50 mm, and the LME series covers 8 to 60 mm. If a machine design uses LMK16UU and LMK20UU in the same build, those are two separate bore sizes and should be listed as separate line items even when the total quantity reaches 100, with the split stated in the enquiry rather than assumed.

MOQ, shaft range and standard reference for the three linear bearing families discussed
SeriesTypeMOQShaft rangeStandard reference
LMUU sealed extended-lengthRound bore, extended sleeve100Not stated in this record; confirm with the supplierJIS B 1185
LMK double-length flangeFlanged, double length1006–50 mmNot stated in this record; confirm with the supplier
LME metric flangeFlanged, metric1008–60 mmDIN ISO 10285

The practical consequence is straightforward: bulk pricing negotiations start at 100 pieces per line item, and the mix of bore sizes within that order determines how much of each size the supplier has to schedule. Buyers who expect to run 60 pieces of one size and 40 of another should raise the split with the supplier, in writing, rather than present it as a single 100-piece order and assume it qualifies.

Batch consistency: seals, sleeve length and load rating

Bulk ordering is not only a quantity decision. The parts in the first carton and the parts in the last carton have to behave the same way on the assembly line, because a bearing that fits slightly differently can stall a build. Three specification points determine what consistency should be checked against in these lines.

Seals on the LMUU series

The LMUU series uses dual-lip NBR seals. The seal is the part that protects the rolling elements from dust and keeps lubricant in place, and its operating temperature range is stated as minus 30 to plus 110 degrees Celsius. That range describes the seal material, not the whole bearing assembly; a buyer specifying a bulk order for a high-temperature application should treat the seal rating as the first check and confirm the rest of the assembly separately with the supplier.

Sleeve length and bore geometry

The LMUU extended sleeve is 35 mm. This matters in bulk because the extended sleeve changes the housing length required and the portion of shaft the bearing occupies. If a design was sampled with a standard-length unit and then scaled up on the extended-length LMUU, the mounting bore and shaft support should be rechecked against the 35 mm sleeve before placing the 100-piece order.

Load ratings that differ by family

Load figures are stated for the family and size being ordered, and they are not interchangeable between lines. The LMK16UU double-length flange unit is rated at 2350 N dynamic, while the standard LMF16UU is rated at 1370 N dynamic. The LM16UU unit in the sealed extended-length line is rated at 1580 N dynamic and 2450 N static. These numbers describe the listed ratings for those units, not a guarantee of service life under a particular load profile. In a bulk order, the rating figure should be matched to the duty cycle the machine actually applies; a buyer who sampled the LM16UU and then moves to the LMK16UU for a flanged requirement should check the load change rather than assume the flanged version carries the same rating.

Batch consistency therefore has two sides. One is manufacturing repeatability, which the supplier controls and the buyer verifies by inspecting shipments. The other is specification consistency, which the buyer controls by keeping the line item, seal type, sleeve length and rating unchanged across the release, or by documenting any change before it reaches the purchase order.

A shipment check that makes the first side concrete: verify the series and bore size on each inner-pack label against the order schedule, measure the sleeve length on a sample against the 35 mm figure, inspect the dual-lip NBR seals for damage, and confirm the load rating printed or stated for the lot matches the unit ordered. What is checked, how many units are sampled and in what form the record comes back should be agreed with the supplier before the first bulk release, because that agreement is what turns an inspection into evidence.

Price breaks: what is quoted and what is not

Price breaks for these linear bearings are quoted per quantity tier and must be confirmed with the supplier. No percentage or fixed unit price is published here, and a buyer should not infer a discount schedule from the MOQ alone. What can be said is how the tier structure is normally framed: the 100-piece MOQ is the entry point for bulk ordering, and above that quantity the supplier quotes a price for the specific tier requested.

  • Tier 1: the 100-piece MOQ line item.
  • Higher tiers: quoted against the actual quantity in the request, including any split across bore sizes.
  • Mixed orders: the split of sizes and flange versus round-bore types should be stated up front, because the quoted tier depends on how the request is structured.

A request that names the series, bore size, quantity and any packaging requirement gives the supplier enough to quote a tier. A request that asks only for a discount on a bearing family is likely to come back with a question rather than a figure. The useful move for a buyer scaling from samples to volume is to send the exact line-item schedule and ask for the tier price against it.

It is also worth separating the sample stage from the bulk stage. Sample-first practice is standard, and some product families offer small sample quantities; the MGN series, for example, offers 5–10 piece samples. This article makes no sample claim for the LMUU, LMK or LME lines, and a buyer moving into one of those families should confirm the sample arrangement with the supplier before relying on it.

Packaging and labelling for bulk delivery

Packaging is the part of a bulk order that is easiest to leave to default and hardest to fix once the goods are on the water. For linear bearings, three packaging decisions affect the assembly line.

Unit protection

Bearings are precision components and the seals and bore surfaces must arrive undamaged. The dual-lip NBR seals on the LMUU line are the exposed part most likely to be affected by rough handling or moisture. A bulk order should specify the unit protection expected: individual wrapping for high-cleanliness assembly, tube packing where sleeve length and bore protection matter most, or a defined carton arrangement for higher-volume lines handled by pallet. Which of these the supplier can provide, and at what cost, is a question for the quotation stage.

Carton and inner-pack labelling

In a 100-piece order containing more than one bore size, inner-pack labelling is what lets the receiving team separate the sizes without opening every carton. The line item should state the bore size and series on the label, for example LMK16UU, LM16UU or LME20UU, and the quantity per inner pack. A bulk order that arrives with a single generic carton label shifts the sorting work to the buyer's warehouse.

Outer packaging for transport

Outer carton strength, palletisation and any moisture protection should be matched to the shipping method. This is a packaging specification, not a lead-time question, and it belongs in the purchase order rather than in a follow-up email after the goods ship. Buyers who need a particular pallet footprint or a maximum carton weight should state it when the order is placed.

How to specify a bulk order

The following order-level details are what distinguish a bulk request from a sample request. They can be listed in a single schedule attached to the enquiry.

  1. Series and type – LMUU sealed extended-length, LMK double-length flange, or LME metric flange.
  2. Bore size – stated per line item; for LMK this falls within 6–50 mm and for LME within 8–60 mm. The LMUU shaft range is not stated in this record, so confirm the available sizes with the supplier before specifying that series.
  3. Quantity per line item – with the total at or above the 100-piece MOQ, and any split across bore sizes stated explicitly.
  4. Seal and temperature requirement – where the dual-lip NBR seal's minus 30 to plus 110 degrees Celsius range is relevant, state the operating temperature so the seal choice can be confirmed.
  5. Load rating check – the dynamic and static figures for the chosen size, matched to the duty cycle.
  6. Packaging – unit protection, inner-pack labelling with series and bore size, and outer carton or pallet requirements.

Price breaks are quoted against this schedule, not against a general request. A buyer who supplies all six points gets a tier price that can be compared with alternatives; a buyer who supplies only a family name gets a question back.

FAQ

What is the MOQ for LMUU, LMK and LME linear bearings?

Each of the three families has an MOQ of 100 pieces. The figure applies to the line item; how bore sizes are split within that 100 should be confirmed in writing with the supplier before the order is placed.

Can I mix bore sizes in one bulk order?

Mixed bore sizes mean separate line items, each carrying its own quantity. Whether the combined total satisfies the MOQ is a commercial point the supplier has to confirm, so state the split in the enquiry instead of assuming the total of 100 across two sizes qualifies.

Are price breaks published?

No. Price breaks are quoted per quantity tier and must be confirmed with the supplier for the specific line-item schedule requested.

Which standards apply?

The LMUU sealed extended-length series references JIS B 1185 and the LME metric flange series references DIN ISO 10285. No standard reference is stated in this record for the LMK series; a buyer who needs one should ask the supplier directly.

What packaging details should be in the order?

Unit protection, inner-pack labelling showing series and bore size, and outer carton or pallet requirements. These belong in the purchase order, not in post-shipment correspondence.